All Weather® Exterior

Lifetime Garantee
Lifetime Guarantee

Guaranteed against blistering, flaking or peeling if applied on suitable and properly prepared surfaces, according to painted directions.*

*Conditions apply 

Nanoguard Technology
Nanoguard® Advanced Technology

Taubmans All Weather® Exterior is engineered with Nanoguard Advanced Technology, which provides maximum protection for exterior surfaces against everyday dirt and stains. The interlocking molecular structure utilises small and large particles to form a strong protective shield, so the surface can be cleaned without compromising the quality of the paint.


Taubmans All Weather® Exterior

Low Sheen
Ideal for all exterior walls, cement render / masonry, trim, roofs, timber, galvanised iron, PVC piping and steel. Not suitable for surfaces used to collect drinking water. Gloss level: 10 - 15%
Matt
Ideal for exterior walls, cement render / masonry, trim, timber, galvanised iron, PVC piping and steel. Not suitable for surfaces used to collect drinking water. Gloss level: 3 - 5%.
Gloss
Ideal for exterior walls (recommended for weatherboards, roof and trims), cement render / masonry, timber, galvanised iron, PVC piping and steel. Not suitable for surfaces used to collect drinking water. Gloss level: 70 - 75%.
Semi Gloss
Ideal for exterior walls (recommended for weatherboards, roofs and trim), cement render / masonry, timber, galvanised iron, PVC piping and steel. Not suitable for surfaces used to collect drinking water. Gloss level: 20 - 25%.

Surface Preparation
Surfaces must be clean, dry and free from all surface contamination. Treat mould with bleach then rinse with fresh water.
New Work
Timber - Weathered (greyed) timber must be sanded to the original timber surface. Tannin rich timbers such as cedar should be primed with Taubmans 3 in 1 Prep or a suitable Taubmans oil based wood primer.
Galvanised Iron - Thoroughly degrease new surfaces. Weathered surfaces should be thoroughly cleaned before painting.
For structural galvanised iron, abrade with 240 grade paper to remove chemical treatments and allow full adhesion.
Cement Render/Concrete - Allow masonry, cement render and mortar to cure for 28 days before painting.
Steel - Remove rust and prime with a suitable Taubmans iron & steel primer or White Knight Rust Guard® Metal Primer.
ZINCALUME® STEEL - Wash with water and mild detergent. Surface must be clean and dry. Apply one coat of Taubmans 3 in 1 Prep.
Repaint
Remove all loose and flaking paint. Spot bare areas with Taubmans All Weather Exterior Low Sheen or the appropriate primer. Apply Taubmans 3 in 1 Prep to aged enamel systems to provide intercoat adhesion. Thoroughly sand new or unweathered Colorbond.®
After Painting
Avoid exposure to steam for 48 hours. Surface may be washed after 7 days, but always avoid abrasive cleaners.
Coats
Minimum two coats. Apply a third coat for superior performance (depending on substrate - coverage will be lower on rough or absorbent surfaces.
Clean Up
Water: Scrape excess paint from equipment into a separate container. Wash up with water. Do not dispose of paint or wash water into drains or sewers.
Coverage
Up to 16 square metres per litre (depending on substrate).
Recoat
2 hours at 25°C (allow 4 hours in cold or humid areas)
Stirring
Stir paint with a wide flat stirrer in a circular lifting motion for at least 5 minutes before use. It is a requirement to stir paint before use to ensure that the colour tints are dispersed evenly throughout the paint. Continue stirring at regular intervals during application. Where more than one can of the same colour and product is required for a job, mix the contents of all the cans together to ensure colour consistency.
Temperature
Do not use at temperatures below 10°C, above 35°C or when humidity is excessive.